|
请注意:澳洲对工具类产品的定义和标准要求为:4 H& d' p: r# j+ B1 H
Tool – portable type
" ^) Z; Y9 g1 m9 ?9 PAn electrical appliance which:5 |% g5 z+ T, Y5 M, X7 X- P/ L
• is for machining, drilling, sawing, or surface preparation; and' Y& W5 ~5 u G! M, e; H3 u
• may be entirely supported by hand during operation6 P6 p) T( ?/ [& z, @) x
but does not include:
: b" s5 a# A# Q$ q: j0 b2 @8 B• a tool, portable type, promoted exclusively to industry.
. d6 B: I2 _4 F: A1 P5 l1 \( t+ z; W• Class specification: a heat pump.
6 G$ d/ O. H U' W' iDrill
: V, P* j1 j/ g" H+ ^; Z" K7 N A& X: N4 l) p3 i( ^9 }# l
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.1:2003.
. Q& F9 c( d. X2 a& S. H$ L2 zSander or polisher (other than disk types)+ [( s2 ] _ N+ d- W
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.4:2003.
* ]2 P1 M# k2 Y/ i V4 T5 r& q) w( sCircular saw# A, n# R N L' o0 F3 A$ I
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.5:2003.2 B$ K( b) Y* j2 Y9 H. `5 y0 R' g
Jig or sabre saw& a4 ^/ E$ I" o% \* a8 x
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.11:2003." D9 W( O2 ~. I! {9 S. A& n
Planer
7 X) H# M- |9 z) I2 MAS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.14:2003.
7 {3 G7 X3 f2 @( E2 [Router" y$ g5 k$ `5 a) e4 ]0 C0 k3 _
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.17:2003.
0 z; O0 M" j* S. aOther
, e" p8 M( l. g/ yAS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001.
9 y' x/ `/ o$ g' o. y7 B9 ~
; |$ M+ w- h2 A2 \* D9 [台式工具并不属于以上范围,只能申请自愿认证,而且因为没有相应的澳洲标准,所以只能由认证部门说了算。 |
|