|
请注意:澳洲对工具类产品的定义和标准要求为:
; f& g( T$ v8 RTool – portable type
4 b t: s0 ]2 j. I+ N/ KAn electrical appliance which:
8 B7 [1 l1 d! v5 A$ [• is for machining, drilling, sawing, or surface preparation; and
& m( v9 T* v* N; ^. K _• may be entirely supported by hand during operation
" v" A& H% y8 f( r, {but does not include:
; H5 Q) |/ J& g" l• a tool, portable type, promoted exclusively to industry. x s3 `9 p! O/ J& _# W0 x9 n9 d
• Class specification: a heat pump.
2 a7 H* t( W- u4 ]7 EDrill
& F. K8 b6 U* V7 ~6 @! y' Y n" {( E# N' F
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.1:2003.1 c/ h8 {! v$ Q7 J0 k1 g% _" y' U
Sander or polisher (other than disk types)' s6 N$ \6 _) b% ?/ l$ b5 E
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.4:2003.
9 r$ P1 W$ M) K* ZCircular saw1 T4 O5 ^; O! q5 m- L+ ^
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.5:2003.0 K+ r+ B0 S$ M& y0 _) n, W+ J
Jig or sabre saw
" q5 B4 w3 ^9 v, O3 kAS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.11:2003.* m# y" X; o, M. p* o
Planer4 P9 {7 S1 i) d) V, M
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.14:2003.
- f) l2 J+ G8 I' I! u& `* o' bRouter
% r- d# R0 B0 b6 n# C. z1 D R" |AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.17:2003.# w1 O5 F1 _5 ~) D$ g
Other
8 ?# x. w4 G) J3 A2 x# xAS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001.
- ^ {* O [3 ?6 T4 X- t: a4 o# h. k [+ h, a, U K
台式工具并不属于以上范围,只能申请自愿认证,而且因为没有相应的澳洲标准,所以只能由认证部门说了算。 |
|