关于UL1082标准7.11疑问

myhet

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

7.10 An opening in the enclosure that has a minor dimension of less than 1 inch (25.4 mm) is acceptable
% c7 t- X! J- _4 @9 P$ V7 Hif a probe as illustrated in Figure 7.2, inserted through the opening, cannot be made to touch any
9 a1 {5 U3 Z, ]uninsulated live part of film–coated wire that involves the risk of electric shock. The probe shall be applied
8 G. _) [9 V2 ^: r& o" o( ~in all possible articulated positions before, during, and after insertion.
# q, U' d9 F$ m7.11 An opening that has a minor dimension of 1 inch (25.4 mm) or more, in an enclosure, as illustrated
2 J# q) _8 M( |7 Din Figure 7.3, is acceptable if, within the enclosure, there is no uninsulated live part or film-coated wire
8 _$ L: L+ O4 e# f! e4 |less than;
a) R distance from the inside edge of the perimeter of the opening and
b) X distance from the plane of the opening.
- h2 C; k( p: ], z- P* uT equals the enclosure thickness, R equals X minus T, and X equals 5 times the diameter of the largest
round rod that can be inserted through the opening but not less than 6-1/16 inches (154 mm). In
. z0 W0 x3 z; Q. s2 ?evaluating an opening, any barrier located within the volume is to be ignored unless it intersects the
boundaries of the volume in a continuous, closed line.

/ x$ C8 C8 R2 a" o( z2 L7.11是否说在一个符合7.3描述的外壳上，当有大于或等于25.4mm的开口时，如果在外壳的以下范围内没有uninsulated live part or film-coated wire的是可以接受的？
% U$ O! D8 c* v5 |5 h这个范围是：A，从开口内边角算起的R距离间。R=外壳厚度+X
            B，从开口平面算起的X距离间。X=MAX.（5*Rod直径，154mm）

simondai

个人理解:
  \# L6 |2 b: j6 ^4 V( }7.11 当产品的外壳上有如图7.3那样的一个开口,并且此开口的最小边长度大于等于1英寸时,如果能够满足：
0 A: ^: W/ M6 s
Ａ）在以开口内边为中心，距离为Ｒ的周长范围内，同时
. b, C, D# X1 l8 @+ L: ?% {( MＢ）距开口外表面Ｘ距离的范围内

( @, x- ~; S9 e没有任何未绝缘带电体或者漆包线，则认为是可接受的．
$ R) ~/ N/ r; A* h/ j! t
& h* f# b$ F4 d: m/ U2 k! iＴ为外壳厚度，Ｒ等于Ｘ－Ｔ，并且Ｘ应当等于最大可伸入开口圆棒直径的５倍但不应小于６－１／１６英寸．在评估开口时，任何挡板都应当被忽略除非该挡板在外壳上的投影可以和开口２边外壳形成一个连续封闭的线．