|
|
| DSH 005/05' @ n$ S. i, o) _( P. o, T' ^
" _" j( X/ C* j5 c+ W
| Luminaires provided with LEDs, a4 m! N, q P0 D# |3 m
| General Section 12* I( y. q* A7 X( q$ H7 I- I
| 60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-2(ed.1);am1;am2 & 60825-1(ed.1);am1;am24 s5 n5 [: [ d) ?9 T
|
+ F% |( x' W2 y& M+ [9 U+ I# Z" q- {Standard: IEC/EN 60598-1
4 [) E2 R6 m7 PIEC/EN 60598-2-6/ w- [4 E( u, s. M; A; K! V
IEC/EN 61347-2-2& E- x2 e( s& U% A5 f
IEC/EN 61347-2-11' O6 Q* A w& {- X a
IEC/EN 60825-1
- @2 ?9 ~* o8 S- v! j- K1 mSub clause: General
# e/ l; h2 ~# QSection 12* J" z2 L9 z/ |$ V1 U+ [
Sheet N°: 005/05" d8 B0 J6 _. g/ K; K; @/ j
Page: 1(1)0 Y! c2 W( ^& L5 ^
Subject: Luminaires provided with$ F1 d; L9 o9 J7 ^/ D) E% Q N6 Q
LEDs4 w9 [4 h$ f( @2 s" Y) {* {) q
Key words:- K' g/ ?7 w& a, y! q M L( K
- Control gears
4 S: }+ r6 v% _- Section 12
8 N4 R4 m% s+ p0 F2 p/ Y, j- IEC/EN 60825-10 k4 `2 H% a) d4 G
Meeting:3 K4 ~9 g/ x+ K9 h+ r* k) e
CTL No. 423 {5 ~ Z, z6 F- U
WG1 No. 1 - 2 - 31 ~. u6 N- w3 t
Item: 10.5.1
: s: A$ p. {* ~" _* D$ t2 o5 yQuestion: Is it possible to issue approvals on luminaires provided with LEDs light source?$ S7 ?, E: `& k: a6 Q; k
Decision: Yes, provided that:; G3 Y; x/ ?$ i7 H9 A) }
(1) The LED circuit is verified according to IEC/EN 61347-2-2 (*) or IEC/EN" ] e. A& s) S. M
61347-2-11. If the laser emits radiation in the wavelength range from 180 nm to 1. }) o+ T4 o4 f# a9 l1 G" Z) D4 W
mm, the LED shall also be tested according to IEC/EN 60825 –1 (Safety of laser
; b' N( f: v5 @3 R. vproducts). Only LEDs classified as Class 1 lasers can be used without problems
! \* F+ c3 Q% L* H& z/ b* Gfor lighting purposes without protection.9 {6 s1 [) V9 o. e; H
(2) The thermal tests required in Section 12 of IEC/EN 60598-1 are carried out as
, O6 f* R3 K. k; ~follows:6 w. t( l, f: Y! j
(a) Luminaires (Class I or II) with built-in control gear can be tested) T3 w/ g; p c5 \
according to the requirements of IEC/EN 60598-2-6.& o+ ~, F/ l+ }0 X3 `, d
(b) For Class III luminaires, the luminaires manufacturer shall provide on" M) A8 l" x ?) L: k- V" E
the instructions all the necessary information to supply the LED circuit
2 O" K; a: T) w! Q5 m" tcorrectly or shall inform the Testing Station about the trade mark, the type( b5 J2 _& m" d
and the technical characteristics of the appropriate control gear. There can
7 h, f9 M' O& q$ I5 R5 D Ibe three different control gears: the type and the trade mark indicated by the
' x* Z: S7 w- T# d. T2 A, K/ bluminaire manufacturer; an electronic control gear clearly specified on the) L) V# u, q7 K0 B. C G$ r, C- y
luminaire instructions; a ferromagnetic control gear. The tests shall be
, N4 s6 c% I q) K4 hcarried out as required in Section 12 according to IEC/EN 60598-2-6 with( F/ K0 F8 n3 D( O/ W& T, N. ?
the appropriate control gear.
- Y+ T+ l7 `* p; V(*) When IEC/EN 61347-2-13 will be published, it will takes over IEC/EN# i5 s5 ]9 z# N5 u2 V
61347-2-2.' k) B' |& o \- V D
# u1 e3 F! X4 ?5 M& [( {5 S7 E- I7 ~% |$ F$ f8 z% H0 N
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册安规
x
|