最近针对EN 60335-2-14出了一个新的EK1决议, 646-16,主要是针对搅拌机这类产品申请GS的一些变化。
) z& |: y* @( {+ P
) n/ t9 M1 l( ~7 E, m3 F% C20.2 The test probes arenot applied to feed openings having a throat with the following dimensions:
$ z8 Z6 A# G1 r这里把a throat with 删掉了,一般的搅拌机没有送料口的,所以这里没什么影响。
2 A' x5 ?/ c; A6 W
7 v6 V C# x6 h3 W @For blenders, detachableparts, except lids, are not removed. The test is carried out with a test probesimilar to that of test probe B of IEC 61032 but having a circular stop facewith a diameter of 125mm instead of the non-circular face, the distance between the tip of the test finger and the stopface being 100 mm. 把这段话删掉,这个影响就很大了,之前拿掉杯盖,用测试手指外加一个125mm挡板的手指去碰刀片,现在把125mm的挡板去掉,直接用测试手指去,意味着只能用挡板为50mm,长度为80mm的测试手指B来触碰。对于盖子没有连锁的玻璃杯,塑料杯或者是金属杯来说是影响比较大4 l$ ^% e2 G2 B2 Y3 _
5 y0 D1 f% F+ A% S
1 r: h) e3 \: t+ r20.112: The cuttingblade of food processors shall stop within 1,5 s after the lid has been openedor removed. Compliance is checkedby operating the appliance without load and at the highest speed." d. i+ x3 Q+ {& M/ g: ?* D) x& a
把盖子拿掉,1.5秒刀片要停下来。原来该条款只适用于food processors,现在blender也需要考虑该条款,需要增加刹车装置,保证打开盖子刀片能在1.5s内停止。
4 V3 c6 e$ w5 s* f( D" \
" R- k% J K2 ^# h% q; K4 x/ F20.113 The lidinterlock of food processors shall be constructed so that accidental operationof the appliance is prevented. Lid interlock switches shall be biased-offswitches.If there is aninterlock between the lid and the main switch, the lid shall be locked when theswitch is in the on position. When the lid is not correctly closed, the switchshall be locked in the off position. Compliance ischecked by inspection, by manual test and by applying test probe B of IEC 61032.
8 ]; l% F2 {0 a$ U原来该条款只适用于food processors,现在blender也需要考虑该条款,用标准测试手指B不能启动微动开关。
% q; N0 ?$ D# l- R9 R0 b
$ Z- V T! L( U( u' {20.114Access todangerous moving parts of food processors shall be prevented for allcombinations of assembly of detachable parts that may occur in use.Compliance ischecked by the following test. Detachableparts are removed or assembled incorrectly in a manner that may occur in use, suchas the incorrect location or misalignment of the parts. A force not exceeding5 N is applied to the parts in any direction and it shall not be possible totouch dangerous moving parts with test probe B of IEC 61032; K1 C: |- ?" l- w
原来该条款只适用于food processors,现在blender也需要考虑该条款,需要考虑各种配件的不同组合是否能启动产品导致触碰到运动部件的风险。, M; G- k/ b/ X$ B# A! h `
# G$ u! M; M- n G _3 S1 C
风险等级:B,进展中的项目立刻执行该决议,已经签发的证书需要在最多6个月内完成变更或者是取消。
- t3 f# w! G9 G X7 N0 T以上个人见解,有不同观点可以一起讨论。 |