|
johnmark 发表于 2016-8-15 17:16 - G- U d. l+ |- ~
UL 498对插头有测试拨出力的要求吗?今年才接触UL产品上班时间没有太多的时间看标准,UL标准觉得很不好看, ... ' @4 Q. h$ w# Q0 G2 n
91 Retention of Plugs Tests. j3 H4 o" c* R n3 v
91.1 The contacts of a 1-15R, 5-15R, 5-20R, 6-15R or 6-20R configuration cord connector shall retain an
# d8 p, s0 f. E0 dattachment plug so that a force greater than 3 lbf (13 N) is required to withdraw the plug when tested as
9 P* ]9 Z5 _6 O( T0 z+ R! `described in this section.( I8 f, r* u6 {* x. K( t. F T
Exception: A cord connector that has provision for locking the plug in place after the blades have been
! H8 a2 \2 j1 v. Pinserted in the female contacts (such as a rotating collar) is not required to be subjected to this test.
2 z+ U z8 {3 }9 _1 d* S4 L91.2 A cord connector with a spring-activated latching mechanism shall be subjected to this test with its
! t: Y: U8 u7 s5 U! ~- J* F) Dmechanism defeated. See 90.2.; [2 ~. `3 E: o+ ?/ `0 ~1 W! W
91.3 Each of six devices is to be subjected to ten conditioning cycles of insertion and withdrawal of a& U1 u( N# T$ X" u g* A3 B4 h8 E
standard solid-blade attachment plug that has American National Standard detent holes in accordance1 H4 k6 h4 X! e; k
with Wiring Devices – Dimensional Specifications, ANSI/NEMA WD6, in rigidly mounted blades, following1 O+ \6 A) e7 D) r, P
which the plug is to be fully reinserted into the device. The mating plugs are to have the configuration
7 ^% _; z |6 L% B4 D1 ^% _indicated in Table 91.1. A pull of 3 lbf (13 N) in a direction perpendicular to the plane of the face of the! W* x% P4 z" [ F% M! X
cord connector and tending to withdraw the plug from the device is then to be applied to the plug for 1- M: U3 G. M" d/ D0 R- C
minute. The displacement of the plug shall not be greater than 0.079 inch (2 mm).
7 K4 D5 d: j/ M" w- h/ @' MException: Connectors may instead be subjected to the Retention of Blades Test, Section 109.2 and
3 N5 r& G- m5 H( Q9 [8 Z) ~109.3 (conditioning and 3 lb retention).$ P7 U t9 J- p0 \4 F7 a( z
91.3 revised November 16, 2012$ a4 _( r' G% e
5 f" `6 u. }, U: x
109 Retention of Blades Test4 f7 ?/ G$ s# B5 h' i) A
109.1 A flush or self-contained receptacle having a 5-15R, 5-20R, 6-15R, or 6-20R configuration shall be) Y9 \! S6 _' }6 Z. ~+ m2 H
subjected to the retention of blades test described in this Section.6 r1 g; v5 M0 a
Exception: A receptacle having a 1-15R, 5-15R, 5-20R, 6-15R, or 6-20R configuration and not of the
, C/ I6 x, E. X# o* E% Fflush or self-contained type may instead be subjected to the Retention of Plugs Test, Section 114.7 U5 z4 ?' A2 S3 a
109.1 revised November 16, 2012
) r; m8 _! n/ Q109.2 Receptacles having the break-off tab, when provided, removed from one nonidentified terminal are
4 r& q' _- K5 a9 T9 i9 b% w" s7 A- nto be subjected to ten conditioning cycles of manual insertion and withdrawal of a standard gauge, see
* k. U7 i5 B; J! s5 a# y/ ~' AFigure 109.1. Each of six devices is to be tested. The gauge is to be configured as outlined in Table 109.1.$ @5 g5 x" f- b& s3 r1 j( [2 y' Q
The force applied to insert the gauge for any of the conditioning cycles is not to exceed 40 lbf (178 N).- Y- q3 ]7 |* p1 o5 x' o
The gauge is to have the dimensions indicated in Figure 109.1 but is not to have holes in the outer ends, i- m/ P1 G& ^ P- V' ^+ l- m+ M
of the blades.. N6 ?8 e1 b% t
109.5 Each of the line contacts of the receptacles is to be tested using the test blade illustrated in Figure" u8 {" N0 Z# C& |) R! A& u/ Q
109.2. Each line contact shall be capable of withstanding for 1 minute a static 0.5 lbf (2.2 N) applied to% `4 D% ^' |" O6 b0 ~4 w
the test blade in a direction normal to the plane of the face of the specimen and in a direction that tends' ?* A- \- N9 C T* e& U8 _# E/ [
to remove the test blade, when the test blade is fully inserted in the contact opening. There shall not be1 m5 [2 p1 U: A& v1 O4 y
more than 0.079 inch (2 mm) displacement of the test blade.
+ l6 u9 A! l' r" R& ~$ j W: m. ~6 u3 T( s
: B9 A& D* t( ?2 l$ k6 `' a应该有3处有要求。( g+ G7 K3 p6 s9 x
|
|