标题: 請教UL2089對輸出線材的限制要求 [打印本页] 作者: market 时间: 2011-11-4 12:09 标题: 請教UL2089對輸出線材的限制要求 關於車載充電器UL2089,閱讀在條文中有提到對線材的規定:$ L8 Z& \! y( m) {
1. 只查到Clause 12 Flexible Cords有一些對線材的明確要求,規定了線材型號/長度和AWG Size Table 12.1;# W8 P- T5 S; ~5 F) K: L/ o( \( Z
另外在Clause 12.1下的兩項Exception No.1 and No. 2; * T$ D5 w0 t0 h! z* H12.1 A unit shall be provided with a flexible cord and shall be type SP-2, SPE-2, SPT-2, SV, SVE, SVT, S, SE, SO, SP-3, SPT-3, ST, STO, SJ, SJE, SJO, SJT, or SJTO. The length of cord external to the unit and including the cigarette lighter connector shall not be less than 3 ft (0.9 m) as measured from the end of the cigarette lighter connector to the point of attachment or entry. Cord AWG size shall be in accordance with Table 12.1. 8 m( ^% t/ w# ? r6 _Exception No. 1: Output wiring for Class 2 or Low Voltage Limited Energy circuits may be parallel cord insulated with rubber, neoprene, or thermoplastic having a wall thickness of not less than 0.013 in (0.33 mm). ) ?! G( s1 ?4 O, IException No. 2: For units rated 10 A or less, an equivalent style appliance wiring material (AWM) may be employed. 2 P. y! U2 ^1 \, S; ]7 g6 w& c1 k0 I5 @7 F
Table 12.1 Cord sizes" n2 b' y0 i$ ^5 C9 T; B$ d* v
Adapter input fuse rating, Amps Minimum cord conductor size, AWG 1 G" p: ~% f1 i- x; t+ \10 A and less 18a : h$ b) i3 Q! J( W( G3 a' O12 17+ k) M e$ y u2 j
13 161 s9 x. C8 g$ y# @
18 14! X v* b2 v. a, G& c, x
20 12 3 G5 o* L$ t6 y4 g2 yRemark a: Size not specified for conductors in Class 2 or Low Voltage Limited Energy Circuits.( g, n, O( I5 y% m, }% K5 s& @
: p4 }" \6 E0 X" I ?( J
這個標準我以前沒有做過,對於UL2089的要求不熟悉,同時我也有咨詢過幾位同行,對此看法不一;$ ?4 n% @! F+ K' ~2 G
1). 有的認為既然標準沒有明確寫明是針對輸入還是輸出線的,那麼輸出線也參考這個標準;這樣非常痛苦,想象一下一個才5W約150g的產品拖一條18AWG SPT-2的線,不論是成本或形狀都讓有鬱悶;/ b3 S7 K' `3 [! }* \+ ?7 z
2). 有人認為從條文來看主要是偏向於輸入線而不是輸出線,況且此類產品本身從輸入到輸出全是安全低電壓,輸入線考慮濫用會嚴格要求,但輸出線既然沒有規定可視為不做任何要求? # Y# R" I. l3 A5 W2 \3 M請教這方面的高手,假如我的產品輸入24V,輸出10V0.5A且滿足LVLE要求,在UL認證時會對輸出線怎樣評估才是合格?另外是否不論條文上有沒有注明,例如exception 1,所有UL認證設備中的線材必須是UL認證線才行?(如可行的話我打算用PU彈弓線,這种材質的線一般都是沒有UL認證的,最好用24AWG看是否有可行性)作者: market 时间: 2011-11-4 13:55
有哪些高手有做過這個UL2089認證麼?還望賜教非常感謝!作者: market 时间: 2011-11-4 16:46
問了一些做過此類案件的朋友,表示UL認證線加89N拉力測試通過就可以了.作者: 明天就垒窝 时间: 2012-2-18 13:52
Remark a: Size not specified for conductors in Class 2 or Low Voltage Limited Energy Circuits.! u8 [& n0 x8 `0 d9 o, f
% J! G0 c z- J5 ^* p5 ~9 K
这句话不是说明了,18AWG不是针对Class 2 或者LVLE。