|
| DSH 5902 g( @8 d8 R9 T+ u* D5 n+ c% X
) l) ~9 A9 x. X* C
| Rule for creepage across grooves and similar surface discontinuities& [6 O2 s2 o$ N; m
| IEC60664-1: 1992 cl. 4.2 IEC60335-1: 1991 Annex E IEC60335-1: 2001 Cl. 29 IEC60730-1: 1999 Annex B IEC60950: 1999 Annex F IEC60950-1: 2001 Annex F IEC60065: 2005 Annex E IEC61010-1: 2002 Annex C IEC60601-1: 1988 Notes Figs 39-47 IEC61558-1: 1988 Annex A IEC61058-1: 2000 Annex A IEC60598-1: 2003 - IEC60745-1: 2001 Annex A IEC61008-1: 2002 Annex B IEC60947-1: 2004 Annex G
9 y; h1 C% I5 {! e5 J. t | 60335-1(ed.4) & 61058-1(ed.3) & 60598-1(ed.6) & 61010-1(ed.2) & 60950-1(ed.1) & 60947-1(ed.4) & 61008-1(ed.2);am1 & 60065(ed.7);am1 & 60664-1(ed.1)
$ h' v# Q; N) [+ q+ m |
+ I0 m. D. t/ j. Z$ u, O7 u, uStandard: IEC 60664-1/1992$ q( L, E, @3 m0 N: p1 q) w
IEC 60335-1/2001
2 n+ V2 D8 D# AIEC 61010-1/2002
6 W$ C# ^$ z9 PIEC 61058-1/2000" h+ ^) n; l7 r, F( z
IEC 61008-1/2002) Y) I0 Q+ j% K8 H
IEC 60947-1/2004
" N( z5 a6 a# W: r8 [% fIEC 60598-1/2003
B% f8 j2 }* q0 y. K! EIEC 60065/2005, G+ O1 m `, @, E1 [- M |
IEC 60950-1/2001
* c( k& u) t6 E% J% {! jSub clause:
1 m7 ]! u$ c; M' oSee Table below
4 w/ O+ t+ H: P9 {& H, J) ZDSH N°: 590
) ^; {% c" K( `Page: 1(1)
! Z# I' W6 ~& q" p, }" f" S qSubject: Rule for creepage across
X- U- }4 ?1 x! J! j4 ^4 w, L$ lgrooves and similar3 {+ o, m$ g) @1 @, Z. z2 O
surface discontinuities
6 a v# A$ h1 W/ ^Key words: R+ h6 s+ n, F& ^+ j
- Creepage. l, u( t0 Y/ \' ?/ N" P2 l( L9 U& X
- Grooves, I1 P$ v" I \2 ]
- Conducting path- {" L; M/ g8 _4 y% c
- Shortest distance
& @' u4 K/ [2 ~" {$ [- Through air
" z) F1 U: n. w0 ]( r4 m% X5 k* {0 JDecision approved
" R, ^5 {9 f: G9 T9 e5 oby the CTL during
$ ?/ P- g+ J- r9 k: Gits 43rd meeting in: v# \ c2 F2 ~6 ]2 O
Johannesburg
. Z( B, F/ }4 `+ MQuestion: As can be seen from examples 2 and 6 of IEC 60664-1 sub clause 4.2 corners
' z/ a8 l; W4 A4 l, a3 x# iwith angles greater or equal than 90 degrees are not bridged. IEC 60664-1 does
( C, R2 M3 j# n& f/ }! @not contain specific information at which angle less than 90 degrees bridging
, Q2 d/ K2 D u" k5 V! ^! v/ Fshall be applied. Some of the above mentioned standards specify that bridging8 X/ V3 I* D$ Z
shall be applied for angles less than 80 degrees.
; t! R1 }) \$ P* _$ F KCan this 80 degree rule be applied in general for all standards?- O0 [% d8 t) k/ \" `8 z
Decision: Yes. The 80 degree rule shall be applied in general for all standards. n! O$ F: R9 o! Z& K, R% t
) y1 s i# z5 ^) B8 l5 X
6 G4 Y3 I8 i6 r! ^" ]+ f4 \ |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|