安规网

标题: 请问一些安规机构的MARK是否一定要贴在产品铭牌上? [打印本页]
作者: demon_life    时间: 2007-10-10 10:08
标题: 请问一些安规机构的MARK是否一定要贴在产品铭牌上?
各位前辈,: H. ]" ^* E- I4 |
我做安规工作已经一年多了,但是对于安规MARK的使用还是糊涂,有那位比较清楚的是否可以告知?
6 {+ n$ e/ y# Q* C6 hCCC的我比较清楚,但是像CE,FCC,TUV,SABS等是否通过认证就必须在铭牌上显示出来?
4 @' ?0 ^+ M+ ^% K这些MARK对纸箱有无要求呢?是否获证就可以在纸箱上印刷呢?, w3 t2 \. t& ^; t
在此,先谢谢各位了~
作者: fasten    时间: 2007-10-10 10:14
要求各不一樣, 一家機構也不一樣, 只能具體了來說才行的
作者: demon_life    时间: 2007-10-10 10:28
哦,谢谢~,4 Q$ j% R3 b% P
那可否具体点说CE,和FCC的呢,我现在需要着两家的相关要求,可否告知?+ k( k; ?3 E$ U/ U
1. 铭牌上的要求
  e& r, l; S; r" m5 Y; a2. 纸箱上的要求
  v* ?1 r! v7 E% T谢谢~
作者: 景行行止    时间: 2007-10-10 10:30
就我知道的一般都打上去，毕竟也能体现产品已经获得那家认证机构的的XX认证了！！！铭牌的认证标示对于很多客户来讲很有意义，因为有了认证便表明产品通过了安全等测试
作者: fasten    时间: 2007-10-10 10:38
引用第2楼demon_life于2007-10-10 10:28发表的  :: v) }" M5 E' ]! c6 M( L5 Z
哦,谢谢~,* b4 x* w7 g2 k& S
那可否具体点说CE,和FCC的呢,我现在需要着两家的相关要求,可否告知?
2 y  M" h+ v! `% I; J- C: G" U1. 铭牌上的要求5 c' L. Q% ?- I9 A4 r! ?' y
2. 纸箱上的要求
9 h; P- X, d. V* ?% L' C* U1 U& s谢谢~
ce的
: v6 ^2 s: c  o0 d4 I0 M外箱一般有ce即可, 尺寸參照lvd/emc/md等指令上都有ce標誌的要求的.
- f2 c+ \! D6 |0 v9 S% ]# Ofcc, 沒有仔細研究, 你可以參考一下cfr47的要求, 比如part15就有如下要求:
( Y. H3 i* g4 R1 Z9 R8 J# r4 k0 d3 E8 o2 a
§ 15.19 Labelling requirements." D) m4 k' u0 |* S7 S3 J; Y# x9 u
(a) In addition to the requirements in2 B7 Y7 ~6 o2 g5 m
part 2 of this chapter, a device subject
1 f, `2 X3 R/ G* s+ O8 A3 Sto certification, or verification shall be5 V' e6 M4 M1 [( R  N) J% R2 e' [
labelled as follows:
2 M4 [. K5 ~$ y6 L4 Z(1) Receivers associated with the operation
7 [" J$ }( J" c, n1 hof a licensed radio service, e.g.,
. g2 H8 e& d/ E' {% ]; Y6 m( R5 U$ xFM broadcast under part 73 of this
4 W% P. ~- V4 J9 ]/ w! N) ^- L$ Uchapter, land mobile operation under
" U, I% ?7 v: s/ P5 ^$ z' jpart 90, etc., shall bear the following
5 ]) L$ h* q( ^- X% vstatement in a conspicuous location on7 T1 L, j$ b! R! V2 P8 ?' L3 D& q7 M
the device:
/ D; y9 x8 d9 y7 ~0 C" g5 hThis device complies with part 15 of the* b7 L" x- a. F( x
FCC Rules. Operation is subject to the condition# c/ t3 Y) Y1 y. d* H* T
that this device does not cause harmful
$ ^1 l  c% n; D: j+ P5 F: N% y: U; H1 Ointerference.
+ L, I  g6 A3 p. [: A3 d0 E% b(2) A stand-alone cable input selector
6 E7 _0 r8 E0 `9 k: u  S" Tswitch, shall bear the following statement
/ v- q, a6 @/ H: g4 M3 q: ^5 d$ E# lin a conspicuous location on the9 [5 u2 o" I& U9 M
device:+ o  b+ {3 v! E
This device is verified to comply with part% V6 q" p% \( C5 u
15 of the FCC Rules for use with cable television
- N/ `$ V6 s0 [* mservice.
/ S2 ~; s/ {% J8 X(3) All other devices shall bear the
5 y9 w/ X0 @3 t0 n  Z8 Pfollowing statement in a conspicuous
1 j- n% m& u+ h) A1 E3 hlocation on the device:
: x; Q5 n+ `2 c3 CThis device complies with part 15 of the
# g; C& r) k: O" uFCC Rules. Operation is subject to the following
# P: {( B4 P# \7 z" gtwo conditions: (1) This device may
8 y3 d, e( Y2 H1 z, m- M4 gnot cause harmful interference, and (2) this
& [* \. Z! o  P, kdevice must accept any interference received,0 r5 y# ^+ T% n4 b% w
including interference that may
* w2 V/ s- o1 T' Dcause undesired operation.
$ O; Q- W. [% Q' P, X7 g(4) Where a device is constructed in! a: i  @- I8 k( h/ P" X
two or more sections connected by
8 v4 F6 L: H0 I2 N% lwires and marketed together, the" @4 b0 S. X$ U, b, _
statement specified under paragraph1 j- [9 n. z% B
(a) of this section is required to be affixed
8 Z: e% h) ^0 |- conly to the main control unit.* d" S& J/ r5 I/ r; p* s
(5) When the device is so small or for
4 W4 ?+ M2 _  i% [5 Isuch use that it is not practicable to
; C; w* L9 \  C0 Z% Y: ]; Fplace the statement specified under! y9 W: }6 [! g6 P9 T  y+ q0 i( x
paragraph (a) of this section on it, the& T* M2 Z3 V8 f
information required by this paragraph
3 {; s0 e$ t; m. u, oshall be placed in a prominent location4 k9 g; {& l8 K& ~$ ^8 a
in the instruction manual or pamphlet0 m6 `  ^" z# F1 I( L! z: T
supplied to the user or, alternatively,* H9 b8 ~: N; `) I3 \1 j  D
shall be placed on the container in
6 X, d1 N; [$ o) m. lwhich the device is marketed. However,( Z3 e; z  ?/ c6 [5 S9 I$ V( q
the FCC identifier or the unique identifier,
: t/ n' M% m$ Mas appropriate, must be displayed+ C( ]3 q0 D* p" j" c( `
on the device.9 x& M# j2 g- k  f$ b  V3 U
(b) Products subject to authorization
% V4 I, k' ]/ V8 l0 P. Iunder a Declaration of Conformity- S" M9 L# a% G3 d* I4 c
shall be labelled as follows:! P& |* A1 j. ~0 c2 r
(1) The label shall be located in a
* `4 b% V0 J8 r+ a) j9 e7 Zconspicuous location on the device and1 ?6 Z# w5 P1 P; M7 O; S
shall contain the unique identification
3 i4 T4 Y+ g6 M4 {4 e8 o% \described in § 2.1074 of this chapter and9 @1 y+ h7 e& X$ j
the following logo:
6 q: d% e' y: u6 l5 L(i) If the product is authorized based2 c0 L( d- f% b% ~( L/ r9 L
on testing of the product or system; or
% c/ B0 B" t: k(ii) If a personal computer is authorized$ I/ o; H/ O" u. S& R
based on assembly using separately% H6 }, S4 S# f( n* m
authorized components, in accordance4 Y$ o: V1 S, P# B2 U$ d
with § 15.101(c)(2) or (c)(3), and2 s+ C5 t# \$ _  p4 j$ d
the resulting product is not separately
8 }! W8 R$ n4 v2 J8 i5 Y/ P! Ktested2) Label text and information should
' Y2 @3 ~* @6 ~: hbe in a size of type large enough to be5 q7 e5 F1 s( k2 I$ Y. }  K) k
readily legible, consistent with the dimensions# o+ q$ f2 D- I) o
of the equipment and the- |$ y& W" k) j
label. However, the type size for the3 [6 f' o+ S8 h4 p& n6 Y
text is not required to be larger than# A4 x2 {( z- \1 D* H, A  @
eight point./ p7 L$ T4 ]7 m6 b4 [7 ^
(3) When the device is so small or for5 r. e6 D! Y1 h0 h# X( F
such use that it is not practicable to  X1 m9 Y! L" T- C5 m0 o% t' r( h/ b6 V
place the statement specified under
( s; `: `$ t2 h7 F% N7 N, n: u
9 c& |/ k/ O/ J2 }7 v.......................9 u& x) R. c+ J% r. T, j8 T

4 l; M7 P0 i$ \http://a257.g.akamaitech.net/7/2 ... /pdf/47cfr15.19.pdf
作者: demon_life    时间: 2007-10-11 16:23
好厉害! 不过上面都是英文,翻译起来真头疼~4 |+ n, P! C+ ?6 [2 t
谢谢fasten
作者: cableyzf    时间: 2007-10-11 16:45
不明白你为何有这样的疑问，既然你做了认证，就是为了宣传，让客户知道产品的质量等级。所以只要获得了认证，我就会在所有可能的位置上全部加上。
/ y0 ^; u7 Z+ Z! Y( W* s  h不过有一个例外，比如CCC，虽然获得了证书，但是使用标志时还是要单独申请，所以其他的也要注意此类问题
作者: demon_life    时间: 2007-10-11 16:55
我也很郁闷啊,我是建议我们业务把已通过相关安轨机构认证的标志打上去,
1 y! J0 L; U( b9 z  k! Y但是业务不同意, 说是客户要求的.% y. s2 n: b5 v9 P
真是搞不懂啊.# `3 ^: k: ^% g) C0 U
所以我也不敢随便同意业务这样做,
8 ?% {. b3 }' [! g) N2 l# j9 I- V2 ~因为有些MARK是通过认证就一定要体现在label上的,像CCC
2 H6 g9 K& f8 _9 c但是有些是对此没有要求的.
作者: cableyzf    时间: 2007-10-11 17:12
单纯从规定上来讲是不一定的,比如CCC,你的产品虽然已经通过了认证并获得了证书以及标志使用资格,但是假如客户只是需要这种结构的线,并不在意是否有CCC认证,并且你的产品表面并没有印刷相应的标识,那么你的包装上就不需要也不可以有CCC的标志了.
3 y* c2 t' a/ M9 Q. N2 a1 p反之,如果你的客户已经要求产品必须符合某种认证,但是却不希望其标志体现在铭牌上,这是不是有些不合常理啊.
/ n! L2 M- L. K. L9 C+ K所以我建议你,如果你是搞技术或认证的,你就告诉你的营业,如果产品上印某些标识,则在铭牌上必须要有相应的标志,这是标准要求.
5 O/ A9 v+ h: o* n# ]' r这样既有利于产品宣传,有有利于产品统一,何乐而不为呢



欢迎光临 安规网 (http://bbs.angui.org/) Powered by Discuz! X3.2