标题: 再谈电容放电测试新版标准要求Discharge of capacitors in equipment [打印本页] 作者: bban 时间: 2009-7-16 14:28 标题: 再谈电容放电测试新版标准要求Discharge of capacitors in equipment 60950二版标准中的: 0 R2 O+ l" s# [7 _: V" U3 V2.1.1.7 Discharge of capacitors in equipment ^( n/ i1 U! N% E2 [. B$ }% cEquipment shall be so designed that, at an OPERATOR-accessible external point of disconnection3 |5 ~( ]2 e# Z' a# n
of a MAINS SUPPLY, the risk of electric shock from stored charge on capacitors connected in the: U2 ~$ a; C. e! w
equipment is reduced. No test for shock hazard is required unless the nominal voltage of the , z0 v0 ]9 C" M8 ~0 WMAINS SUPPLY exceeds 42,4 V peak or 60 V d.c. 9 Y/ E% i. l( {7 c* D1 k" r' l6 V3 @; Z
中说到连接到Mains supply的电压没有超过42,4 V peak or 60 V d.c值就可以不必测试。但是接下来说 ( i: i+ a% i8 }2 c5 S- {4 o 2 F/ i" d( t0 j$ w# }) AEquipment is considered to comply if any capacitor having a marked or nominal capacitance# w! R' e6 F2 z! O9 @0 l/ P
exceeding 0,1 μF and in circuits connected to the MAINS SUPPLY has a means of discharge 0 ^& N4 e) x. ?; h4 ?! |( G5 d- q! Iresulting in a time constant not exceeding:& t/ d& U; d( _/ O* P8 O+ q
– 1 s for PLUGGABLE EQUIPMENT TYPE A; and4 j* `# U: N7 F" F
– 10 s for PLUGGABLE EQUIPMENT TYPE B " h- i% T W% P/ X9 I- |. { 0 S' [, T# V; n3 E4 I! J& e' B, w在连接到Mains supply的电路中有容量超过0,1 μF的电容则要求考虑1s或者10s之后储存在电容电压电压值没有超过规定的值没有超过42,4 V peak or 60 V d.c值或者衰竭到最大的37%一下, ( }$ W+ h% n6 P& G2 K/ ~: J+ X! s1 L; s, K! i* r1 |1 n( J4 V) M# v
在这里假如产品连接到Mains supply的电压没有超过42,4 V peak or 60 V d.c.,但是电路中有超过容量0,1 μF的电容,那究竟是不要测试呢??作者: lao_xia 时间: 2009-7-16 15:10
我們應該從觸電危險這個方嚮來看的話,在沒有超過42,4 V peak or 60 V d.c的電源中不存在觸電危險當然就不用做這個測試的。作者: bban 时间: 2009-7-16 15:37
引用第1楼lao_xia于2009-07-16 15:10发表的 : 8 j9 N* [# G7 m' L/ D* I我們應該從觸電危險這個方嚮來看的話,在沒有超過42,4 V peak or 60 V d.c的電源中不存在觸電危險當然就不用做這個測試的。
. s/ U# {- y# l( s ^4 \6 O# B2 a1 Q" ?9 Q3 W* C
正解,如果从触电危险这方面考虑的话,连接到AC mians supply的产品沒有超過42,4 V peak or 60 V d.c,可以不用做这个测试。9 E# U! S; x# [! n' g
但是从能量危险角度看,如果产品连接致DC mains supply的沒有超過42,4 V peak or 60 V d.c产品,当有0.1uf的电容时候,从标准上面看考察的是能量危险,测量2S之后的电压值再换算成能量焦耳,是否要和连接AC mians supply电容放电测试方法一致呢?