安规网

标题: 如何对电吹风分离电路做39.3.3和39.3.4?UL859 [打印本页]

作者: shixiafeng    时间: 2009-5-30 17:21
标题: 如何对电吹风分离电路做39.3.3和39.3.4?UL859
如何对电吹风分离电路做39.3.3和39.3.4?UL859
/ f# y* A" T  G' ^3 C7 w6 ?The air inlet opening shall be gradually obstructed until the operation of all circuits is interrupted) z! V5 B+ W  }6 g
by the functioning of a limit or a temperature control, or until ultimate results are otherwise obtained0 X! u, B9 U5 h6 O# F. K( r1 z
39.3.4.2 The air outlet is to be gradually obstructed using masking tape such that approximately 50, 75,
* j4 N. D  W6 x$ F, [90, and 100 percent of the outlet opening area is progressively blocked for 3 minutes at each of the four
9 _# x( |. C/ C8 e( V2 ^6 zpositions. For each of three samples, the location at which the blocking begins (the top, a side, or bottom)
+ K" v% k0 ~4 e1 U) {. Cis to progress in the same direction in which it was started and is to be such that the limit control will% |$ Q  w( `$ w7 Z3 H0 @0 G6 V. T" s
remain in the air flow for the longest possible time as blocking progresses. If temperatures cause* o. l/ |. X2 f6 Z: R6 v' P; E3 u: j
degradation of the tape, or if the use of tape would cause deformation of an outlet nozzle, a metal plate
/ U) D& N2 x# A, [or other material resistant to combustion may be used to block the outlet opening. If the final 100 percent- n1 v$ H1 h$ M
blockage test does not result in interruption of all heater and motor circuits by a limit control, the test is to) p4 u$ ?+ m, {1 ~- a3 _6 y
be continued, at 100 percent blockage, for 7-1/2 hours, at which time ultimate results are considered to
5 t; Z1 F1 a6 T0 w( zbe achieved.
$ t8 v1 K" W8 p1 c. I: J是不是TCO动作了不停止了,还是做到最终结果或者是FUSE开路?
作者: feel100%    时间: 2009-5-31 10:05
分离线路$ d5 }* x. Z( b, U
对于堵入风测试,做到FUSE Open如果盖上十层毛巾FUSE还没断开的话,就盖着十层毛巾运行7.5h' s' g# o7 [- j4 V8 x

. s! P( C) B* S6 V, d对于堵出风测试也一样是做到FUSE Open,或堵到100% fuse还没断开的话,就堵着100%运行7.5H
作者: xuewenfei    时间: 2009-5-31 10:15
提示: 作者被禁止或删除 内容自动屏蔽
作者: tianchi0305    时间: 2009-5-31 12:37
第一句中的until the operation of all circuits is interrupted  就说明是要所有的线路都要断开,而分离线路中TCO动作是还有功率的所以要等FUSE断开
作者: lsj7250    时间: 2009-6-5 19:10
如果是分离线路,跳制先断开后,马达在工作,是否算通过?请指教?
作者: xuewenfei    时间: 2009-6-5 19:30
提示: 作者被禁止或删除 内容自动屏蔽
作者: shixiafeng    时间: 2009-6-7 21:54
谢谢指教,解决了我的问题
作者: longclever    时间: 2009-6-8 16:46
提示: 作者被禁止或删除 内容自动屏蔽




欢迎光临 安规网 (http://bbs.angui.org/) Powered by Discuz! X3.2