安规网

标题: 欧标插头表面必须印接地极、中性接和带电极符号吗? [打印本页]

作者: zhjj_201    时间: 2019-7-31 11:44
标题: 欧标插头表面必须印接地极、中性接和带电极符号吗?
     大家好!公司供给客户的欧标插头没有印接地极、中性接和带电极符号,原因是表面涉及欧盟多国认证标志印字省略导致,另外也了解很多其他厂家也存在没有印的。现在客户提出异议,请教高手指点:( L+ M" X4 c  ^
     第一,根据VDE标准,是否必须在插头表面印接地极、中性接和带电极符号?
+ w# C3 Z& p- c9 U/ g7 s     第二,若有必须印,或者可印可不印,有没有相关的标准描述支持,若有,请分享说明下。谢谢!9 C  C7 C- j/ |$ N, r8 H

作者: sfw1984    时间: 2019-7-31 16:29
看看别家的做过认证的实物也可能求证。
作者: 甬城五彩石    时间: 2019-8-8 08:23
插头插座   极性标记及接地符号 必须要的
作者: suxuaner    时间: 2019-9-3 10:38
无疑,必须要求。国内CCC例行检查就包含极性检查,这些必须有。
作者: 448080300    时间: 2019-9-3 13:08
欧标插头参考的标准是IEC60884,此标准对于Marking的要求(如下)没有说明要印接地线、中性线和带电极符号,所以是可以不用印的。
# e$ l" V" \) W& L
( q, r+ ~' O' A' c$ `& ^2 W2 A/ L8 Marking. v4 M; B* ^: \7 c. Z3 C
8.1 Accessories shall be marked as follows:7 u* f; [) f* |; `4 \; m8 a
– rated current in amperes;
+ Z" r2 U; n  Q; ?. b/ `/ L4 F, `– rated voltage in volts;* y7 ?/ ?& j+ V
– symbol for nature of supply;
' a; P$ S: n: y3 o  `, N– manufacturer's or responsible vendor's name, trade mark or identification mark;$ m( Y/ l- R' V
– type reference which may be a catalogue number;/ t+ [! Z- z# x- \7 Y  `
– first characteristic numeral for the degree of protection against access to hazardous parts# U! y* o% [4 D- n5 n! f
and against harmful effects due to ingress of solid foreign objects, if declared to be higher
8 m/ h' z: `# d7 o" ?* y7 b1 r# tthan 2, in which case the second characteristic numeral shall also be marked;" t" V- u* K6 E) W& L" h0 J
– second characteristic numeral for the degree of protection against harmful effects due to  |7 B% }' o0 |. U. U& l# R
ingress of water, if declared to be higher than 0, in which case the first characteristic
8 Z3 G0 }8 w) m: i4 H$ Z7 ~1 d$ knumeral shall also be marked.
" q8 j8 v- V4 ?If the system allows plugs of a certain IP rating to be introduced into socket-outlets having" |- f$ D0 }* k9 Q' F; q
another IP rating, attention should be drawn to the fact that the resulting degree of protection. f; G4 O, l8 b" u
of the combination plug/socket-outlet is the lower of the two. They shall be stated in the3 P) K" o* l  U7 V9 D7 E* m& z* j
manufacturer's literature related to the socket-outlet.
作者: 448080300    时间: 2019-9-3 13:10
suxuaner 发表于 2019-9-3 10:38* B" \( u- k( g4 G( c0 E- v
无疑,必须要求。国内CCC例行检查就包含极性检查,这些必须有。
) F& Z4 K$ u- A
CCC插头参考的标准是GB 2099.1-2008 家用和类似用途插头插座
. [: a. y7 t+ f; j- F) B9 ]% E, N此标准对插头的印字是有明确要求印中性极、接地极、带电极的符号,与欧标插头是不一样的。




欢迎光临 安规网 (http://bbs.angui.org/) Powered by Discuz! X3.2