安规网
标题: AC inlet 本體上是否必須要印上安規logo [打印本页]
作者: 年華 时间: 2016-9-22 16:28
标题: AC inlet 本體上是否必須要印上安規logo
請問一下，AC inlet有申請RU ,CCC,VDE,SEMKO,NEMKO ....,這些安規logo是否必須要印在inlet上面？謝謝
作者: H-RH 时间: 2016-9-22 18:40
是必须的!
作者: 年華 时间: 2016-9-23 08:42
H-RH 发表于 2016-9-22 18:40 
/ Q5 x2 X. [0 j是必须的!
2 D4 x7 R# O3 u2 |7 e) o謝謝回覆，我有查了UL，檔案裏面寫的是需要印廠商名字和材料型號，沒有說一定要把RU印上去呢，
作者: H-RH 时间: 2016-9-23 08:57
年華 发表于 2016-9-23 08:42
, R2 Z6 [5 E" a謝謝回覆，我有查了UL，檔案裏面寫的是需要印廠商名字和材料型號，沒有說一定要把RU印上去呢，
当真?5 j' ^$ m: ]5 b) a/ t* J/ Q
通常 UL 档案内有一个叫 EXXXXX-VolX-RecCompMarkData.rtf 的文件, 内有这样说明:
8 k5 r2 x6 m. l. ?) }! a7 J/ i9 r- M; x8 n, ?
Recognized Component MarkingData Page (RCMDP)
(File Immediately After Authorization Page)
RECOGNIZEDCOMPONENT MARKING % R2 Z- M/ K7 J! k8 E! i. B
Products Recognized underUL’s Component Recognition Service are identified by marking elementsconsisting of:& s3 P6 t0 |' e& J% z6 [$ F* M; Y
% }/ R# o1 ~/ E& {. }
1. The Recognized Company’s identificationspecified in this document.
* [. c; Z+ k: e
2. A catalog, model or other applicable productdesignation specified in thedescriptive sections of this document.
5 K6 o; \8 y9 f
3. The UL RecognizedComponent Mark shown below.
. T! G% h" R' }$ I1 i
7 u2 `' l0 R: F6 fOnlythose components, which actually bear the Marking, should be considered asbeing covered under the Recognition Program. The UL Listing or Classification Mark is not authorized for use on or inconnection with Recognized Components.
' F) l& D& I; Y . B( m2 {9 K% B8 ?; q* P
Recognized Component Mark
4 u: H; Q: ^; F0 N+ E
u2 C; g6 L) I- V _[attach]106671[/attach]
: ~0 T5 U7 \8 d& i* _. e
Minimumsize of the Recognized Component Mark is not specified as long as it islegible. Minimum height of theregistered symbol ® shall be 3/64 inch but may be omitted if it is out ofproportion to the Recognized Component Mark or not legible to the naked eye.
$ R* f( P }/ b6 f( y% _2 n; }% T" n# f( w$ u) O. Q+ l
, m' b; \1 n* F/ e1 c1 WThemanufacturer may reproduce the Mark electronically. Any decision regarding the acceptability ofthe manufacturer’s Mark reproduction will be made at the Reviewing Office.
* x( h4 a! t, l9 u3 ^! A% ~( `
2 j) y8 d4 ?! Z8 `) ^. S5 P6 R# Y* }/ R; j/ Z
作者: sophieaplus 时间: 2016-11-15 13:23
頂一下
| 欢迎光临 安规网 (http://bbs.angui.org/) |
Powered by Discuz! X3.2 |