安规网

标题: 求大神指教如何整改 [打印本页]
作者: lengchuan000    时间: 2014-4-18 17:01
标题: 求大神指教如何整改
[attach]86441[/attach]
  g# E4 P5 c7 `$ M1 y' F' Z如图为一支玩具枪的弹射物，黄色部分为EVA材料，端部为黑色塑料，客户指定按照ASTM F963-11来做测试。测试结果是在主轴向拉力施加至50N左右时，不是黑色端部脱落就是黄色EVA从中间断开，脱落或断开部分均为小零件。按照“4.21.1.1 No projectile intended to be fired from a toy shallhave any sharp edges, sharp points, or small parts that would fit within the cylinder shown in Fig. 3.”我判定该样品不符合现行F963的要求。请教给位同行，如果遇到这种案例该怎么判，还有就是如果判定不合格又该如何整改。谢谢
* e4 S. r$ ~$ ^  @3 v
作者: ttyoren    时间: 2014-4-26 21:32
Projectile Toys—These requirements relate to certain,$ t  S7 R: g( R9 [( e, j/ F
but not all, potential, unexpected hazards that might be caused, [9 r( |  l; u2 [+ v; @4 y1 i
by projectile firing toys and by the firing of improvised
; o9 Q, ^- b$ i- Q6 G7 U1 e) T3 eprojectiles from such toys. Certain well-recognized hazards
+ {; O, e2 E1 ~2 X  H8 q  _9 tthat are inherent in traditional toys such as slingshots and darts; Q" j, z1 B# B$ _* H7 }
are not covered by these requirements. The discharge mechanism5 H8 j+ `( S4 w$ T# g
as well as the projectile shall conform to the requirements
8 j. L% J0 G" k/ ~6 Lspecified in this section after testing in accordance with the
/ B6 Z7 W9 h) [1 T# l' `1 Z, kappropriate test methods described in 8.5-8.10 and 8.14.) n9 R: M( q0 A5 M) Y- T: H" N
肯定不合格 弹射物也要做滥用测试的。 & B- b, N6 U" i9 \7 |8 `/ |
改的话 个人认为就胶水粘牢一点
作者: lengchuan000    时间: 2014-4-29 16:49
ttyoren 发表于 2014-4-26 21:32 * S1 m9 A0 {! C/ f" T, E3 b, J' k
Projectile Toys—These requirements relate to certain,
) k4 ~( G9 E- c0 E/ j  tbut not all, potential, unexpected hazards t ...

( `1 h* M: w( J. b$ `. }2 A我也判为不合格，但是客户说拿到香港BV，对方什么都没说就出给报告了，还说美国海关对这方面也不是特别在意
作者: scanf2008    时间: 2014-9-9 14:36
这样的情况要看脱落或者断裂后是否还可能用弹射器发射，如果不能用来发射的话也是合格的。



欢迎光临 安规网 (http://bbs.angui.org/) Powered by Discuz! X3.2