标题: 60335-1泄漏电流测试方法的问题 [打印本页] 作者: Alexsong 时间: 2013-7-25 18:19 标题: 60335-1泄漏电流测试方法的问题 在60335-1标准中分别有13.2条的工作温度下的泄漏电流测试和16.2条的在潮湿处理后的泄漏电流测试。 " o( L6 p4 L3 x$ W. Y8 p/ j6 \ C在13.2条的测试比较好理解,那对于16.2条的测试各位是如何做的呢? + \9 V$ O1 p" F16 Leakage current and electric strength * B4 j( E6 C& r16.1 The leakage current of the appliance shall not be excessive and its electric strength shall be adequate. & d( F9 M; r4 f3 \2 [: cCompliance is checked by the tests of 16.2 and 16.3. ( r* ]8 e; }# S! NProtective impedance is disconnected from live parts before carrying out the tests.9 Q. G2 p* ]) h) n7 u The tests are carried out on the appliance at room temperature and not connected to the supply mains.$ n0 J9 @6 v. O# ?% p! d
16.2 An a.c. test voltage is applied between live parts and accessible metal parts that are connected to metal foil having an area not exceeding 20 cm × 10 cm in contact with accessible surfaces of insulating materials. ; U3 D& m) g/ F; d( C6 }8 U' {: c' kThe test voltage is' m2 i3 S4 F+ {6 v6 x
– 1,06 times rated voltage, for single-phase appliances;6 B8 ~9 z0 ~3 ^. w( m
– 1,06 times rated voltage, divided by 3 , for three-phase appliances.) l% \- I& T$ P' m" o' _& r w6 F
The leakage current is measured within 5 s after the application of the test voltage.作者: hgf397556998 时间: 2013-7-25 19:31
16.2的泄漏电流是在器具不工作的状态下测试的!作者: Alexsong 时间: 2013-7-26 12:49
如何测,能不能具体些作者: zhangrui110 时间: 2013-7-26 14:40
买台泄漏电流自动测量仪就搞定了,不用麻烦作者: Alexsong 时间: 2013-7-26 18:09
在16.2的测试条款里根本就没有提到泄漏电流测量网络,而且是不通电进行测试,所以我不知道你买个泄漏电流自动测量仪怎么搞定作者: tianyg2006 时间: 2013-7-26 19:55
安全隔离变压器用什么样的?作者: 山炮 时间: 2013-7-27 09:50
NεLN·16.2ò磬豸迹2k裬迹裩й1mA迹220k2kйй涨γ作者: 山炮 时间: 2013-7-27 09:51
买个转换头,一边是插头,一边是万用孔。拆开,将插头的N脚拔掉,将插座的L、N短路。以后用来打高压也很方便。16.2中没有要求使用测试网络,如果设备没有去除网络的选项,这问题不大,它的阻抗可以视为是只2k欧电阻,而被测产品呈现的阻抗(不等同绝缘电阻)很高,简单地估算,泄漏电流1mA时,阻抗达220k欧,远远大于2k欧,不会影响结果。如果产品是大泄漏电流产品,可直接用电流表测不用泄漏电流测量仪,因为:标准的规定本来就是直接用电流表测的。测量时要注意标准中允许值加倍的情况,更要注意电压是否施加到应测的绝缘上,这是因为测量时产品是不工作的,存在电压施加不到绝缘的情况,也可能形成过大的分压。作者: 北边的素言 时间: 2013-7-28 18:05